<address id="npnhb"></address>
    <dfn id="npnhb"><dfn id="npnhb"><menuitem id="npnhb"></menuitem></dfn></dfn>

          <form id="npnhb"></form>

              <sub id="npnhb"><listing id="npnhb"><menuitem id="npnhb"></menuitem></listing></sub>

                <address id="npnhb"></address>

                  产品展示
                  PRODUCT DISPLAY
                  产品展示您现在的位置: 首页 > 产品展示 > 台湾仪鼎PICOTEST > PICOTEST测试讯号转换器 > J2110APICOTEST仪鼎仪器专业测试讯号转换器

                  PICOTEST仪鼎仪器专业测试讯号转换器

                  更新时间:2017-08-09
                  浏览次数:595
                  简要描述:

                  PICOTEST仪鼎仪器专业测试讯号转换器专业代理销售现货供应INJBOI,INJB02,INJB03,J2100A.J2101A,J2102A,J2110A,J2111A,J2112A,J2120A,J2130A,J2140A,J2160A,J2180A,J2180A-20,J2190A

                  在线咨询

                  PICOTEST仪鼎仪器专业测试讯号转换器

                  J2110A Solid State Voltage Injector 

                   
                   
                   
                   
                   
                  iconDC~45MHz的頻寬可支援溫度及機械控制(loop band width< 1Hz)和zui高性能調節器及放大器量測
                  icon優異精確的低失真表現
                  icon25Ω串接插入電阻
                  icon50Ω 輸入阻抗(OSC port)
                  icon< 3uA偏壓電流
                  icon> 2 MΩ輸入電阻(IN port)
                  icon可配合通用輸入型的高PSRR 低噪音穩壓器(J2170A)使用
                  icon詳細規格
                  PICOTEST仪鼎仪器专业测试讯号转换器J2110A测试讯号转换器
                   

                  While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.

                  The selection of a valid injection point in the circuit is more critical when using a solid state injector than with the transformer injector. The solid state injector presents an infinite impedance between the points of injection. In order to provide correct results one side of the measurement must present a much higher impedance than the other side. In a typical power supply control loop, the voltage sense divider is generally a good injection point, since the output impedance of the power supply is very low compared with the impedance of the voltage sense divider.

                  The solid state injector has a limitation in the operating voltage, with the majority limited to 10V or 12V. This is not the amplitude of the injection signal, but the peak value (positive or negative) of the signal operating voltage.

                  PICOTEST仪鼎仪器专业测试讯号转换器
                   
                  Specifications
                  CharacteristicRating
                  Maximum Vcc±12V
                  Maximum Icc20mA
                  Maximum Input Voltage DC+AC±10.5V
                  Maximum Output Voltage±10.5V
                  Offset Voltage3mV
                  Bias Current8uA
                  3dB Bandwidth (-10dBm)DC ~ 40MHz
                  Temperature range0 ~ 50°C
                  Maximum Altitude6000 Ft

                  J2100A 1 hz - 5 mhz
                  J2101A  10 hz - 45 mhz
                  J2110A
                  J2120A
                  J2130A

                  J2140A

                  J2160A

                  J2180A

                  J2180A

                  J2190A

                   

                  联系方式
                  • 服务热线:

                    4009023318

                    13913158248

                    15295666126

                  • 公司电话:

                    0512-66315386

                  • 公司传真:

                    0512-66315383

                  在线客服
                  • 技术支持:
                  • 产品咨询:

                  最近中文字幕2018免费版,日韩精品无码免费专区网站,东北女人毛多水多牲交视频,一本加勒比HEZYO无码专区
                  扫一扫访问手机站扫一扫访问手机站
                  访问手机站